News

Our company has developed a variety of plate cutting machine tools, including electric, mechanical, hydraulic and so on 1. Main Features: 1) Totally EU streamlined design,Monoblock by welding robots & aparatus and stress relief process by Annealing treatment. 2) Adopt integrated hydraulic system, more reliable and easy for maintenance.and the hydraulic system from Bosch-Rexroth,Germany, 3) The Hydraulic Guillotine is a Swing Beam Action machine which is produced in a variety of cutting lengths and capacity options. 4) The distance of the backgauge is adjusted by the motor and is well adjustment is displayed by E21S with Delta inverter. 5) Equipped with lighting-alignment, so as to align when shearing. The stroke of knife beam can be adjusted in stepless mode. 6) Safe fence and the electric inter locker have been designed for the machine to ensure the operation safety to CE regulation. 2.Standard Equipment: 1) Estun E21S NC control system 2) Powered Back guage X-axis 3) DELTA Inverter controlled back guage 4) HIWIN Ball screws &Polished rod with 0,05mm accuracy 5) Squaring Arm and Front Support Arms 6) Germany Bosch-Rexroth Hydraulic 7) Germany EMB Tubing connector 8) Germany Siemens Main Motor 9) Telemecanique/Schneider Electrics 10) Hydraulic &Electrical overload protection 11) Top blade with two cutting edges and bottom blade with four cutting edges.(6CrW2Si)

Conventional Plasma Cutting This process uses oxygen, air, and nitrogen for cutting. Conventional plasma cutting is a lower cost solution that will produce good quality cuts, but there will be some angle to the cut surface and the minimum hole quality is 3:1 to the plate thickness. Most conventional plasma systems run 65 amps, 85 amps, 100 amps and 200 amp systems. Mild steel cutting can be achieved from gauge material to 1-inch production pierce. Stainless steel and aluminum can be achieved from gauge material to 3/4-inch. Hi-Definition Plasma Cutting This process uses multiple gases for producing the highest quality parts. The hi-definition plasma uses the following gasses for cutting: oxygen, air, nitrogen, argon/hydrogen, and argon/nitrogen. If outfitted with an Auto Gas System, this plasma also has marking capabilities by using low amperage from the power supply. Argon gas is used for this marking process which is used to identify parts, bend lines, layout lines or drilling locations. This hi-definition plasma system will produce high quality cuts, and the angle to these parts is very minimal. Hole cutting quality on Mild Steel is a minimum of 1:1 ratio to the plate thickness up to a 1-inch plate. Quick change plasma torch heads make changing consumables fast and easy. Hi-definition plasma systems range from 130 amps, 260 amps, and 400 amps. Mild steel cutting can be achieved from gauge material to 2-inch production pierce. Stainless steel and aluminum cutting can be achieved from gauge material to 1-1/2 inches and with an 800 amp plasma system can production pierce up to 3-inches stainless steel.

The modernization level and scale of machine tool industry is one of the important signs of the industrial development of a country. The traditional manufacturing power of machine tool industry is mainly Germany, Japan, Italy and other industrialized developed countries. At the same time, with the improvement of the overall strength of the domestic industry, China has become a machine tool manufacturing power. At present, in terms of supply, China's machine tool industry ranks first in the world with an output value of 19.42 billion US dollars, accounting for 23.1% of the global market share. In terms of demand, Chinese consumption ranked first in the world, accounting for 27.2 percent of the global demand market with a total consumption of 22.3 billion U.S. dollars. Although China occupies an important market share in the global machine tool supply and demand market, it is a machine tool power, but it is not a machine tool power, and middle and high-end models still rely on imports

Hydraulic Ironworker machine is the mutifution product of the punching and shearing machine which can cut , punch , notch and bend all kinds of materials such as plate , flat bar , square bar , round bar , equal , angle, channel ,I-beam and so on According to the transmission system can be divided into mechanical and hydraulic The small Ironworker machine is suitable for all kinds of site work, it is convenient to move the machine, change the mold is also very fast, can quickly complete Angle steel cutting, punching. Plate punching, cutting and other functions The heavy-duty Ironworker machine is suitable for batch blanking in steel structure factory, and can complete punching and cutting of medium thickness plate, cutting of Angle steel channel steel and other profiles, pipe and tube notching and so on Ironworker machine is a very cost-effective machine